برد کنترلر پرینتر سه بعدی MKS Gen V1.4

برد کنترلر پرینتر سه بعدی MKS Gen V1.4 به همراه كابل

کاربرد برد کنترلر MKS Gen:

1. دستگاه‌های CNC
2. پرینتر‌های سه بعدی

مشخصات برد کنترلر MKS Gen:

1. برای سخت افزار از ساختار RAMPS1.4 استفاده شده است.
2. قابل تطبیق با 5 عدد استپر درایور های 4988/8825
3. PCB چندلایه 
4. محافظت از آسیب دمای بالا به برد
5. پشتیبانی از ورودی تغذیه 12 تا 24 ولت 
6. توانایی اتصال مستقیم به Ramps1.4 ، 2004LCD control panel و 12864LCD control panel سروو ها و
7. رابط های AUX-1 ، AUX-2
8. مشابه Ramps1.4 دارای 3 خروجی 5 ولت و 3 رابط خروجی 12-24V
9. دارای 4 درایور MOSFET برای hotend0 ، hotend1 ، bed و فن خنک کننده 
10. دارای فیوز قابل تعویض برای محافظت از اتصال کوتاه
    

مستندات:
Firmware و درایور MKS Gen V1.4

Description:
At the heart of any 3D Printer, CNC Router, or other machine is a controller board. The controller runs the firmware and operates all the functions of the machine. A 3D Printer controller will control the motors, heated bed, extruders, and anything else that is present on the 3D Printer. Different machines will have varying requirements from a controller board, such as the compatible firmware, pin outputs, or just the raw power required. It should be taken into consideration are the mechanical motion of the machine, number of the extruders, type of stepper motors, and the voltage you wish to use throughout the machine.

MKS Gen is a feature-rich all-in-one electronics solution for Reprap and other CNC devices. It features an onboard ATmega2560. Its five motor outputs are powered by Pololu pin-compatible stepper drivers. The board features a developer-friendly expansion port supporting giving access the same as Ramps1.4. MKS Gen is designed to be flexible in the user's power source availability, allowing any power supply from 12V-24V.

Application:
CNC machines
3D printers

Features:
1, Mega 2560 and ramps1.4 set on a board, to solve complicated Ramps1.4 combination of interfaces, the problem of failure prone.
2, replace the motor drive, drive and support 4988 8825 drive.
3, the circuit board with high-quality 4-layer, heat and made a special optimization; ramps are 2 shelves.
4, using high-quality MOSFET, and better heat dissipation.
5, using a dedicated power chip, support 12V-24V power input, the voltage converter chip to solve the heat problem Ramps.
6, can accept 24V input power under the same system can be hot-bed current is reduced to 1/4, an effective solution to the hot bed MOS pipe heat problems.
7, the firmware can use open source firmware Marlin, ramps1.4 identical configuration and can directly replace Ramps1.4.
8, can be connected to the control panel and 12864LCD Ramps1.4,2004LCD control panel.(Can't be sure to match all of stype of 12864LCD and 2004LCD )
9, reserved for motor pulse and direction output ports for easy plug-in high-current To add a large current (eg 2A, 5A) motor drive circuit.
10, reserved Ramps1.4 on Servos, AUX-1, AUX-2 interface that provides three 5V output, three 12V outputs