ماژول سنسور اندازه گیری جریان اثر هال 5 آمپر WCS2705

WCS2705 Module

5330-79-8512

811,000 تومان
کالا موجود است
موجودی انبار : 2 عدد


خرید کالا


علاقه مندان : 2 نفر
وضعیت : فعال

تعداد مرجوعی : 0
دنبال کنندگان : 2 نفر

قدمت : 2 سال و 1 ماه و 21 روز
وزن : 10 گرم

کل فروش : 7 عدد
تعداد سفارش ها : 6 سفارش

هنوز هیچ رایی ثبت نشده است
ماژول سنسور اندازه گیری جریان اثر هال 5 آمپر WCS2705

ماژول اندازه گیر جریان مدل WCS2705 برای جریان های دی سی و متناوب کارآیی دارد و در هر یک را در محدوده جدایی اندازه گیری می کند. این ماژول اندازه گیر بر اساس سنسور جریان WCS2705 ساخته شده که از دسته سنسور های اثر هال است.
این ماژول اندازه گیر جریان دو عملکرد اساسی و مهم دارد: یکی تقویت سیگنال با تقویت کننده تفاضلی LM39 و دیگری ارسال سیگنال برای دستور به رله.تغذیه ماژول WCS2705 در محدوده  3 تا 12 ولت است اما پیشنهاد می شود از ولتاژ 5 ولت ثابت برای تغذیه این ماژول استفاده شود.


کاربرد سنسور جریان WCS2705 :

  1. تست مدار محافظ جریان
  2. توسعه سیستم ها
  3. تست کحافظ اتصال کوتاه

مشخصات WCS2705 Module :

  1. چیپ: WCS2705
  2. ولتاژ ورودی: 3 تا 12 ولت
  3. ولتاژ ورودی پیشنهادی: 5 ولت
  4. جریان ورودی: 3.5 آمپر
  5. محدوده اندازه گیری: جریان متناوب 5 آمپر، جریان ثابت 7.5 آمپر
  6. رزولوشن تشخیص جریان: 255mV/A
  7. تعداد پین: 4 
  8. شناسایی سیگنال خروجی بیش از حد
  9. دمای عملیاتی : 75- تا 125 درجه سانتی گراد
  10. ابعاد: 30 در 37 میلی متر

مستندات:
دیتاشیت سنسور WCS2705 Module


Description:
WCS2705 Current Detection Sensor Module [ 5A AC] is an electrical current sensor that can accurately detect both DC and AC current based on WCS2705 Hall Effect Base Linear Current Sensor chip. This chip has 2 important parts of an accurate low-temperature drift linear hall effect detector with temperature compensation and a current path through an ultra-low resistance 8.3 mΩ. internal conductor to reduce power dissipation, better respond to temperature results in more reliability and stability. Due to the passing the current trough this conducting, a magnetic field is created, which is detected by the hall sensor part and presented as a proportional voltage signal.
This module has two essential functions of an analog sensed signal that pass trough an op-amp and ready to feed an A/D converter and creating a switching signal for activating the relay. A specified current applies to the comparator as a limited current (overcurrent, undercurrent, short circuit current, etc.) that when the sensed current is greater than the limit current, the switching signal is changed from a low level to high level and activate the relay.
The WCS2705 module can be supplied with 3V up to 12V DC (5V is recommended) and 3.5mA current for detecting current in the range of zero up to 5A AC or -7.5 up to +7.5A DC. The limited current can be set from 0.16A up to 5A, so this module can be used as current protection from 0.16A up to 5A AC/DC.

Application:
Smart car motor overcurrent detection
stall protection current detection
short circuit protection testing
demonstration teaching experiments and other occasions to facilitate the secondary developmen

Features:
Chip: WCS2705
Input Voltage: 3V ~ 12V
Recommended Input Voltage: 5V
Input Current: 3.5mA
Current detection range: DC: ± 7.5A , AC: 5A
Current detection resolution: 255mV/A
Output overcurrent signal indication;
Overcurrent signal is set critical point adjustable, set the resolution 0.4A;
With mounting holes for easy firmware installation;
Sampling current conversion analog signal output, which can be accessed ADC, TTL level signal output, which can be accessed microcontroller IO port control.
Pin Number: 4 Pin
Operating Temperature: -20°C ~ 125°C
Size: 30mm x 37mm