آی سی توسعه دهنده ورودی-خروجی MCP23017-E SS

MCP23017-E SS IC

7384-345-11709

88,880 تومان
کالا موجود است
موجودی انبار : 15 عدد


خرید کالا


علاقه مندان : -
وضعیت : فعال

تعداد مرجوعی : 0
دنبال کنندگان : -

قدمت : 1 سال و 9 ماه و 14 روز
وزن : 1 گرم

کل فروش : 20 عدد
تعداد سفارش ها : 8 سفارش

هنوز هیچ رایی ثبت نشده است
چیپ افزاینده ورودی خروجی MCP23017-E/SS
** توجه : آی سی با پارت نامبر MCP23S17 میباشد و رابط SPI **
آی سی MCP23017-E/SS جزو آی سی های توسعه دهنده ورودی-خروجی طبقه بندی می گردد. این آی سی محصول برند Microchip Technology می باشد. این آی سی دارای تعداد 16 ورودی-خروجی می باشد. رابط کاربری آن نیز به صورت I2C می باشد. این آی سی دارای وقفه خروجی می باشد. این آی سی دارای مشخصه POR بوده و خروجی آن از نوع پوش-پول است. جریان خروجی سورس و سینک آن 25 میلی آمپر با فرکانس کلاک 1.7 مگاهرتز است.
ولتاژ تغذیه ای آی سی توسعه دهنده 1.8 ولت تا 5.5 ولت است.
پکیج و فوت پرینت این آی سی 28-SSOP با نصب به صورت سطحی یا SMD و دمای کاری در محدوده منفی 40 درجه سانتیگراد تا 125 درجه سانتیگراد است. 

کاربرد آی سی توسعه دهنده I/O مدل MCP23017-E/SS:

  1. افزایش پورت های ورودی خروجی I2C
  2. توسعه سیستم های امبدد

مشخصات آی سی توسعه دهنده I/O مدل MCP23017-E/SS:

  1. تعداد ورودی خروجی: 16 عدد
  2. رابط کاربری: I2C
  3. .وقفه خروجی: دارد
  4. ویژگی: POR
  5. نوع خروجی: پوش-پول
  6. جریان خروجی (سینک/سورس): 25 میلی آمپر
  7. حداکثر فرکانس کلاک: 1.7 مگاهرتز
  8. ولتاژ تغذیه: 1.8 ولت تا 5.5 ولت
  9. دمای کاری: منفی 40 درجه سانتیگراد تا 125 درجه سانتیگراد
  10. نوع نصب سطحی یا SMD
  11. پکیج فوت پرینت: 28-SSOP
  12. کارخانه سازنده: Microchip Technology

مستندات:
دیتاشیت MCP23017-E SS IC


Description:
The MCP23017/MCP23S17 (MCP23X17) device family provides 16-bit, general purpose parallel I/O expansion for I2C bus or SPI applications. The two devices differ only in the serial interface.
The MCP23017/MCP23S17 (MCP23X17) device family provides 16-bit, general purpose parallel I/O expansion for I2C bus or SPI applications. The two devices differ only in the serial interface:
• MCP23017 – I2C interface
• MCP23S17 – SPI interface

The MCP23X17 consists of multiple 8-bit configuration registers for input, output and polarity selection. The system master can enable the I/Os as either inputs or outputs by writing the I/O configuration bits (IODIRA/B). The data for each input or output is kept in the corresponding input or output register. The polarity of the Input Port register can be inverted with the Polarity Inversion register. All registers can be read by the system master.
The 16-bit I/O port functionally consists of two 8-bit ports (PORTA and PORTB). The MCP23X17 can be configured to operate in the 8-bit or 16-bit modes via IOCON.BANK.
There are two interrupt pins, INTA and INTB, that can be associated with their respective ports, or can be logically OR’ed together so that both pins will activate if either port causes an interrupt.

Application:
I2C and SPI interfaces
embedded system developing

Features:
16-Bit Remote Bidirectional I/O Port: - I/O pins default to input
High-Speed I2C Interface (MCP23017):
- 100 kHz
- 400 kHz
- 1.7 MHz
High-Speed SPI Interface (MCP23S17):
- 10 MHz (maximum)
Three Hardware Address Pins to Allow Up to
Eight Devices On the Bus
• Configurable Interrupt Output Pins:
- Configurable as active-high, active-low or open-drain
• INTA and INTB Can Be Configured to Operate Independently or Together