ماژول انکودر 8 کاناله PPM ورژن 2

8CH Encoder PPM

7577-129-11906

483,480 تومان
کالا موجود است
موجودی انبار : 8 عدد


خرید کالا


علاقه مندان : -
وضعیت : فعال

تعداد مرجوعی : 0
دنبال کنندگان : -

قدمت : 10 ماه و 28 روز
وزن : 6 گرم

کل فروش : 2 عدد
تعداد سفارش ها : 2 سفارش

هنوز هیچ رایی ثبت نشده است
ماژول انکودر 8 کاناله ورژن 2 مناسب پیکسهاوک و APM
برخی از کنترلرهای پرواز مانند خلبان خودکار Pixhawk فقط از گیرنده های سازگار PPM (مدولاسیون موقعیت پالس) پشتیبانی می کنند. اگر یک گیرنده PWM (مدول شده با عرض پالس) دارید، به یک رمزگذار PPM نیاز دارید تا بتواند با یک FC فقط PPM کار کند. این رمزگذار PPM ورودی های معمولی PWM را در یک خروجی PPM رمزگذاری می کند. این به شما امکان می دهد تا حداکثر 8 کانال را از یک گیرنده RC معمولی به یک ورودی PPM سیمی برای کنترلر پرواز خود ترکیب کنید.
PPM Encoder v2.0 به پورت‌های خروجی سروو PWM هر گیرنده R/C متصل می‌شود و آنها را به یک پالس PPM مناسب برای بسیاری از خلبان‌های خودکار کدگذاری می‌کند.
توجه داشته باشید اگر قرار بر استفاده از این ماژول 8CH Encoder PPM دارید، حتما گیرنده های خود را کالیبره کنید و از باتری استفاده کنید زیرا که پورت USB ممکن است تغذیه کافی به ماژول نرساند.

کاربرد ماژول 8 کاناله PPM:

  1. اتوپایلوت های پیکسهاوک 
  2. اتوپایلوت APM

مشخصات ماژول 8 کاناله PPM:

  1. دارای 8 خروجی
  2. جنس خروجی: PWM
  3. پروتکل ارتباطی: SPI


Description:
Some flight controllers such as the Pixhawk autopilot only support PPM (pulse position modulation) compatible receivers. If you have a PWM (pulse width modulated) receiver, you will need a PPM encoder such as this one for it to work with a PPM only FC. This PPM encoder will encode regular PWM inputs into a single PPM output. This allows you to combine up to 8 channels from a regular RC receiver to a single wire PPM input for your flight controller e.g. Pixhawk or APM.
A PPM Encoder will allow you to use any older style RC receiver with only PWM outputs for each channel.
The PPM Encoder v2.0 plugs into the PWM servo output ports of any R/C receiver and encodes them into a PPM pulse suitable for many autopilots (e.g. PX4FMU).
The nice thing about PPM is that it will enable you to reduce all channels to a single wire, excluding ground and power lines.
The PPM Encoder does require quite a bit of additional wiring to the receiver.
It uses quite a bit of power making it likely you will need to plug in your battery while doing radio setup with USB cable in Mission Planner.
If you are using this PPM Encoder it is important to know that when you are calibrating your transmitter you may need to hook up your flight battery to the autopilot because the USB port alone can’t supply enough power.

Application:
Pixhawk autopilot
APM

Features:
8 output
output type: PWM
protocol: SPI